#Uncommenting these urls would only enable #the power up auto injection and force injection(test case). #XTRA_SERVER_1=http://xtrapath1.izatcloud.net/xtra2.bin #XTRA_SERVER_2=http://xtrapath2.izatcloud.net/xtra2.bin #XTRA_SERVER_3=http://xtrapath3.izatcloud.net/xtra2.bin #Version check for XTRA #DISABLE = 0 #AUTO = 1 #XTRA2 = 2 #XTRA3 = 3 XTRA_VERSION_CHECK=0 # Error Estimate # _SET = 1 # _CLEAR = 0 ERR_ESTIMATE=0 #NTP server NTP_SERVER=time.izatcloud.net NTP_SERVER_2=asia.pool.ntp.org NTP_SERVER_3=0.cn.pool.ntp.org #XTRA CA path XTRA_CA_PATH=/system/etc/security/cacerts # DEBUG LEVELS: 0 - none, 1 - Error, 2 - Warning, 3 - Info # 4 - Debug, 5 - Verbose # If DEBUG_LEVEL is commented, Android's logging levels will be used DEBUG_LEVEL = 3 # Intermediate position report, 1=enable, 0=disable INTERMEDIATE_POS=1 # Below bit mask configures how GPS functionalities # should be locked when user turns off GPS on Settings # Set bit 0x1 if MO GPS functionalities are to be locked # Set bit 0x2 if NI GPS functionalities are to be locked # default - non is locked for backward compatibility #GPS_LOCK = 0 # supl version 1.0 SUPL_VER=0x20000 # Emergency SUPL, 1=enable, 0=disable #SUPL_ES=0 #Choose PDN for Emergency SUPL #1 - Use emergency PDN #0 - Use regular SUPL PDN for Emergency SUPL #USE_EMERGENCY_PDN_FOR_EMERGENCY_SUPL=0 #SUPL_MODE is a bit mask set in config.xml per carrier by default. #If it is uncommented here, this value will overwrite the value from #config.xml. #MSA=0X2 #MSB=0X1 SUPL_MODE=3 # GPS Capabilities bit mask # SCHEDULING = 0x01 # MSB = 0x02 # MSA = 0x04 # ON_DEMAND_TIME = 0x10 # GEOFENCE = 0x20 # default = ON_DEMAND_TIME | MSA | MSB | SCHEDULING | GEOFENCE CAPABILITIES=0x37 # Accuracy threshold for intermediate positions # less accurate positions are ignored, 0 for passing all positions ACCURACY_THRES=70 ################################ ##### AGPS server settings ##### ################################ # FOR SUPL SUPPORT, set the following SUPL_HOST=supl.qxwz.com SUPL_PORT=7275 # FOR C2K PDE SUPPORT, set the following # C2K_HOST=c2k.pde.com or IP # C2K_PORT=1234 # Bitmask of slots that are available # for write/install to, where 1s indicate writable, # and the default value is 0 where no slots # are writable. For example, AGPS_CERT_WRITABLE_MASK # of b1000001010 makes 3 slots available # and the remaining 7 slots unwritable. #AGPS_CERT_WRITABLE_MASK=0 #################################### # LTE Positioning Profile Settings #################################### # 0: Enable RRLP on LTE(Default) # 1: Enable LPP_User_Plane on LTE # 2: Enable LPP_Control_Plane # 3: Enable both LPP_User_Plane and LPP_Control_Plane LPP_PROFILE = 0 ################################ # EXTRA SETTINGS ################################ # NMEA provider (1=Modem Processor, 0=Application Processor) NMEA_PROVIDER=0 # Mark if it is a SGLTE target (1=SGLTE, 0=nonSGLTE) SGLTE_TARGET=0 ################################################## # Select Positioning Protocol on A-GLONASS system ################################################## # 0x1: RRC CPlane # 0x2: RRLP UPlane # 0x4: LLP Uplane A_GLONASS_POS_PROTOCOL_SELECT = 0 ################################################## # Select technology for LPPe Control Plane ################################################## # 0x1: DBH for LPPe CP # 0x2: WLAN AP Measurements for LPPe CP # 0x4: SRN AP measurement for CP # 0x8: Sensor Barometer Measurement LPPe CP LPPE_CP_TECHNOLOGY = 0 ################################################## # Select technology for LPPe User Plane ################################################## # 0x1: DBH for LPPe UP # 0x2: WLAN AP Measurements for LPPe UP # 0x4: SRN AP measurement for UP # 0x8: Sensor Barometer Measurement LPPe UP LPPE_UP_TECHNOLOGY = 0 ################################################## # AGPS_CONFIG_INJECT ################################################## # enable/disable injection of AGPS configurations: # SUPL_VER # SUPL_HOST # SUPL_PORT # C2K_HOST # C2K_PORT # LPP_PROFILE # A_GLONASS_POS_PROTOCOL_SELECT # 0: disable # 1: enable AGPS_CONFIG_INJECT = 1 ################################################## # GNSS settings for automotive use cases # Configurations in following section are # specific to automotive use cases, others # please do not change, keep the default values ################################################## # AP Coarse Timestamp Uncertainty ################################################## # default : 10 # AP time stamp uncertainty, until GNSS receiver # is able to acquire better timing information AP_TIMESTAMP_UNCERTAINTY = 10 ################################################## # QDR engine availability status ################################################## # 0 : NO QDR (default) # 1 : QDR enabled # This settings enables QDR Configuration for # automotive use case, if enabled then # DR_AP_Service needs to be enabled in izat.conf #EXTERNAL_DR_ENABLED = 0 ##################################### # DR_SYNC Pulse Availability ##################################### # 0 : DR_SYNC pulse not available (default) # 1 : DR_SYNC pulse available # This configuration enables the driver to make use # of PPS events generated by DR_SYNC pulse # Standard Linux PPS driver needs to be enabled DR_SYNC_ENABLED = 0 ##################################### # PPS Device name ##################################### PPS_DEVICENAME = /dev/pps0 ##################################### # AP Clock Accuracy ##################################### # Quality of APPS processor clock (in PPM). # Value specified is used for calculation of # APPS time stamp uncertainty AP_CLOCK_PPM = 100 ##################################### # MAX ms difference to detect missing pulse ##################################### # Specifies time threshold in ms to validate any missing PPS pulses MISSING_PULSE_TIME_DELTA = 900 ##################################### # Propagation time uncertainty ##################################### # This settings enables time uncertainty propagation # logic incase of missing PPS pulse PROPAGATION_TIME_UNCERTAINTY = 1 XTRA_TEST_ENABLED = 1 XTRA_THROTTLE_ENABLED = 0 #################################### #system time injection #################################### XTRA_SYSTEM_TIME_INJECT = 1