Ultimate cure to the 'QHSUSB_DLOAD' of Mi2/S

[davfiala]

OMG. You don't need this thread or qhsusb drivers if you can boot into fastboot. Install regular fastboot drivers.

 

[Manuele]

OMG. You don't need this thread or qhsusb drivers if you can boot into fastboot. Install regular fastboot drivers.

Hi, thanks for your reply.
I think i've already installed regular driver (if regular fastboot drivers are the ones installed with miflash package) but the Mi2s isn't recognized by PC. Exist a method to verify it?

Have you an alternative link for this driver, maybe a standalone version to test if it works? I'm a bit lost

EDIT: I've found this guide, is ok for me?

http://www.tothemobile.com/android-adb-fastboot-drivers-setup-guide-windows

EDIT 2: I found another tools that install fastboot drivers, now i think drivers are ok but the phone is still not detected. Grrr

http://www.tuttoandroid.net/forum/g...astboot-drivers-15-seconds-adb-installer.html

 

[mehdoux]

Hi,

@Manuele : The only way for me to install Mi2S Fastboot Drivers and make the phone recognized by the computer was to install this software (Xiaomi MiSync) (yes i know, it is in chinese, but just have click on next next next, and you don't need the program itself, just the drivvers it installs) : http://miuiandroid.com/windows/

Then, you'll have to flash a MIUI fastboot image and you'll have a brand new phone in front of you.

 

[M1cha]

http://en.miui.com/thread-15465-1-1.html

or better: http://en.miui.com/thread-92720-1-1.html

 

[Manuele]

I've already installed this software and his driver, both in english then in chinese, any signal from connecting my phone.
I try to change usb port from usb 3 to USB 2, nothing change.

I think i test all possible way to debrick, i'm thinking about send it to someone who can repair it, like the assistance service of the shop where i buy the phone....

I can't see any other way

 

[Infinitely]

Guys when you finally are able to unbrick your M2S (miflash says it's successful) you will have to wait at least 10 min for the first bootup! So first xiaomi logo will apear and then 5 minutes nothing. Then the qualqomm snapdragon logo will appear under the screen. And then finally after some time your ROM will boot up! So don't worry, just wait for it to load, it's not bricked!

 

[handyandy]

Hi all,
I tried to merge the partitions of my MI2S but did mistake, no more fastboot, no led, just nothing. Dead !
I tried to unbrick by connecting the 2 test points with battery ground and Miflash, MI2S was recognised by Miflash, but Windows ended the Miflash flashing process before the end(Windows will close this program because an error occured, debug was not working). Installed Miflash on another pc, but cel phone is not detected. Now when I connect it to pc it give a red flashing led for a minute or two, then shuts off.
Battery was full of charge when tried to merge and have a second one for replacement, charged a couple of mouths ago.
Is there a way to restart this device ?
Thanks in advance.

 

[M1cha]

Hi all,
I tried to merge the partitions of my MI2S but did mistake, no more fastboot, no led, just nothing. Dead !
I tried to unbrick by connecting the 2 test points with battery ground and Miflash, MI2S was recognised by Miflash, but Windows ended the Miflash flashing process before the end(Windows will close this program because an error occured, debug was not working). Installed Miflash on another pc, but cel phone is not detected. Now when I connect it to pc it give a red flashing led for a minute or two, then shuts off.
Battery was full of charge when tried to merge and have a second one for replacement, charged a couple of mouths ago.
Is there a way to restart this device ?
Thanks in advance.

I'm not sure if this is a driver problem or not but you could give Miflash4Linux a shot(using a live cd e.g. Antergos).

 

[handyandy]

I'm not sure if this is a driver problem or not but you could give Miflash4Linux a shot(using a live cd e.g. Antergos).

Thanks M1cha, but I'm not familiar with linux at all, it's complicate enough with windows.
Thinking back, I tried to flash without knowing how to use Miflash. I did the mistake to flash the phone while not disabling potential hazardous software in windows and as result that instead choosing the right files in miflash I selected wrong files as they appeared in windows's protected environment. That's probably why when I tried to flash this time the proper way, windows encounter a problem and closed miflash without debugging.
I'm not confident at all if the phone could be restored one day.

 

[vasabhi]

thank you all. my mi2s is come back
after brick 2 week but now is ok.
thank you very much
^_^

 

[hawil]

Hello Everyone, Can someone help me... my device can enter lastboot but miflash tools can't detect my device.. also i cannot update using select update packages.. please help.. Thanks.