Ultimate cure to the 'QHSUSB_DLOAD' of Mi2/S


Hello everyone and sorry for the text use the translator.
I have mi2 dead, is recognized as QHUSB_DLOAD ........
but with miflash wrong has good end.
by mistake ..... problem EMMC and non-compliant file
Who can help me?
 
hello please if you can help with my Mi2S, by turn on only logo of xiaomi appears, the same if I try push volume down+power the recovery menu will not start. When connect to pc through usb it flush red led for second and again logo xiaomi appers and nothing else, windows 7 not recognize any usb device connected. So I tried this cure with wire points, progress was thas windows recognize usb device and succesfull install drivers for qualcomm, than I have start Miflash http://bigota.d.miui.com/tools/MiPhone2.11.6.exe with script flash_all_wipe.bat, ROM for Mi2S I downloaded from http://bigota.d.miui.com/3.9.20/miui_MI2_3.9.20_fastboot_4.1_fjr7c3dccl.exe .So Miflash detect device, klick on flash and it begin, after 370s it ends succesfull. Unplug phone a start it, and again only logo appears nothing else, I try flash it twice but no change. Please do you have some another tips how I can revive xiaomi?
 
hello please if you can help with my Mi2S, by turn on only logo of xiaomi appears, the same if I try push volume down+power the recovery menu will not start. When connect to pc through usb it flush red led for second and again logo xiaomi appers and nothing else, windows 7 not recognize any usb device connected. So I tried this cure with wire points, progress was thas windows recognize usb device and succesfull install drivers for qualcomm, than I have start Miflash http://bigota.d.miui.com/tools/MiPhone2.11.6.exe with script flash_all_wipe.bat, ROM for Mi2S I downloaded from http://bigota.d.miui.com/3.9.20/miui_MI2_3.9.20_fastboot_4.1_fjr7c3dccl.exe .So Miflash detect device, klick on flash and it begin, after 370s it ends succesfull. Unplug phone a start it, and again only logo appears nothing else, I try flash it twice but no change. Please do you have some another tips how I can revive xiaomi?

You could try the official MiFlash to restore the Mi2(s) @ http://bigota.d.miui.com/MiFlash/MiFlashSetup_1.0.12.4120.exe

Run the software and connect your device, if the software detected your device there should be a green button. Click on it and the software will download and flash it back to factory state.
 
Hi. ihave tried the method, but my MI2S stops around 37 seconds in the flash process every time: stating end of file error:
upload_2014-6-25_0-24-16-png.8060
 
Hey, guy.
When you want to repair your bricked M2, you need to get the two test points and the battery holder negative to be short-circuit. It will force the low Level system work.
See the picture.
When exactly I short-circuit? nothing is connected or the usb is in ? How many times? How can we know that I short circuit ?
Thanks in advanced for all the answers..
 
@Natane If you had read post #11 , you would know that these are already answered questions. Short circuit before connecting usb in until you see a QHSUSB_DLOAD hardware in device manager and when drivers are OK take off your bridge, put your battery in or leave as it is and finally flash a rom..
 
@Natane If you had read post #11 , you would know that these are already answered questions. Short circuit before connecting usb in until you see a QHSUSB_DLOAD hardware in device manager and when drivers are OK take off your bridge, put your battery in or leave as it is and finally flash a rom..
 
Hi mi mi3 is detected by miflash it says COM20 but when i try to flash it gives me error . I forgot the error. I flash the fastboot .tgz file extracted it and put it on my desktop.
 
Hi,

I had a crashed LCD and after replacing with a spare one, the phone (Mi2 32gb) cannot boot, only has black screen and weirdly I don't get any LED lights...

I installed the MiPhone_Assistant and MiFlash programs, and the Device Manager find the phone as Android Composite ADB Interface... Then in the MiFlash I could see the Devide id (d6d96590) and the Flash operation finished successfully (tried twice), BUT the phone still stuck at the black screen. Additionally, after the flash and reboot of phone (I only guess it is rebooted, as the screen is black always) the Device Manager recognised it as some device, but not a proper phone.

Where I fail with the process? Does the ADB interface driver cause this issue, and I need to 'short-circle' the phone to be able to flash QHSUSB_DLOAD drivers or there is other known workaround?

Thanks,
Ferenc

What is 'qhsusb_dolad' ?It is the situation when you can't boot into your phone,recovery mode and any other visible interface. When you connected your phone to the PC, the LED will flash and your PC will show that they were searching for the drivers needed(win7/8) but they couldn't find .......If it is commom for you to remove the battery when the phone did not shutdown completely or when you ran into 'No-Response' , as time goes by ,it will be inevitable that you come across the 'QHSUSB_DLOAD' situation .
But from now on ,you needn't worry about that for I have found a way out.
Tools needed:
Hardware: A PC running XP and higher (win7/8 recommended) and your usb cable
Software : MIflash and MIAssistent and a certain mi update rom(It is a *.exe file---fastboot file)
Steps :
1. Install the first two softwares described above(Run as administrator) in your PC (You need to disable the enforcement of digital signature while on win8 in the advanced startup (press 7 or F7)
2.Boot into fastboot mode(you just need to do with your two buttons and usually you cann't see the interface for your screen just won't show in this situation) before connecting to PC
3.Connect you MI2/S to your PC via the usb cable and the pc will recongnise it in the device manager panel(if not, update its driver in the unknown device---qhsusb_dload)
4.Open the miflash and click fresh to load your phone's serial number
5.Flash the update rom(the self-extracted-to folder) into your phone and reboot .

Explanations:
Miassistant contains the 'qhsusb_dload' driver for any phone and it enables the PC(Miflash) to recongnise your CPU serial which is the key part of updating by wire.

Tips:

Try this with your other phone, I believe it will work ,too.

Good luck ,guys !
Are you sure you can not boot your phone to fast boot mode? Press key"volume -" and power button at the same time.

When you connect your phone to your computer via usb port, can you find something called"unknown"on the Device Manager panel?

It's easy to save your dead phone with MiFlash. But I have to translate the Chinese guide to English...My god...

I suggest: First of all, connect your phone to your computer, and if the computer find new hardware"QHSUSB_DLOAD", install the driver, then open the MiFlash, and see whether there is device list on the panel, see the picture. If it is, you can flash it and save it.
If not, you should do the "short-circuit" ...
View attachment 5676
 
why do you want to do that? the software on your phone is fine - your lcd is either defective or connected incorrectly
 
Hello everyone, I have the same problem but with a REDMI NOTE, I watched the pictures to make the connection but the REDMI NOTES is different and near to the contacts of the SIM there are no points where to connect the forceps as images
I removed the back to see if I found them but I have not seen anything that looks like, I include photos of the cell opened, someone can tell me if it is possible to do the same procedure with the REDMI NOTE?
 

Attachments

  • DSCN1052.jpg
    DSCN1052.jpg
    195 KB · Views: 510
  • Like
Reactions: ollan
@kront75 If you can still enter the bootloader, you can try to press volup and voldown same time when powering on the phone.
If not it'll get complicated :p
 
@M1cha the phone shows no signs of life, if I connect it to the charger does not appear nothing, same thing with the pc ... is completely dead:confused:
 
mi2 is the only device with (known) test points. I guess ur mi4 is fully bricked now.
 
thanks for the respond, now what i have to do? if i give to service center they have to change hardware to solve with any additional hardware like JTAG?please advise
 
Hello everyone, I have the same problem but with a REDMI NOTE, I watched the pictures to make the connection but the REDMI NOTES is different and near to the contacts of the SIM there are no points where to connect the forceps as images
I removed the back to see if I found them but I have not seen anything that looks like, I include photos of the cell opened, someone can tell me if it is possible to do the same procedure with the REDMI NOTE?

Just wondering if this issue has been solved ???
 
Hi everyone. I used this method several times and even it ends successfully the mobile doesn't restart at all. Because my wife has same mi2s someone knows how to make a nv backup and restore with Qpst? Thanks.
 
Thanks 1000!!!!!!
My Xiaomi 2S was dead but now it's resurrected!!!

You are the best,
thanks again
 
Hi guys,

I think i've a soft-bricket MI2S. I've some issues with reinstalling miui v6 after a tdb and now my phone can fastboot but can't enter in revocery and can't boot normally, it stops at miui logo.
Reading this topic i try first with miflash, but cell is not recognized like QHSUSB_DLOAD (I've tried with 3 pcs, win xp, win 7 and win 8.1) so i can't install Qhsusb Dload Driver found in a later post.
At this point i try to short circuit but my mi2s is not recognized anymore by PC, nothing appears like a new device.

It's fully bricked? Seem strange because i can put it in fastboot, can see mi logo e can turn on/off normally...

Thank you in advance and excuse me for my bad english